ML210 Technical Resources

Documentation Index

Select a model of ML210 from the contents pane on the right to view the technical resources. The model number can be found on the bottom of the unit.

Opening the case

The ML210 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.

  • Ensure your body is discharged of any static electricity by touching a grounded metal surface.
  • Remove the 6x phillips screws on the outside of the case.
  • If your unit has COM ports, remove the standoffs for those as well.
  • The backplate will then be loose and can be removed.
Note: Pull gently as to not tear the EMI gaskets.
  • Note the ridge between the lid and the heat block on the processor
  • Insert a flathead screwdriver into the ridge and pry them apart using a twisting motion.
  • Tilt the lid to a 45 degree angle and pull it loose from the rest of the case.
  • You now have full access to the internals

ML210G-10 / TM200

Drivers

https://drive.google.com/open?id=1eRuRkf04GJgetcXScZrmqeE3NRmvD5uW

Motherboard Manual

https://drive.google.com/open?id=1WBrh4LQuMyYY_Tr93q21alaeRNu6rNt0

Enable Auto Power On

● Power on the unit and press the Del key repeatedly to access the BIOS
● Once in the BIOS, navigate to the Chipset tab
● Arrow down to the “Restore AC Power Loss” option
● Enable it
● Save & Exit
● Auto power on is now enabled

Clear the CMOS

Note: This procedure requires opening the case first. Instructions for opening the case can be found here.

● Locate the clear CMOS jumper next to the purple header
● Move the jumper over by 1 pin
● Wait 30 seconds
● Restore the jumper to the original position
● The CMOS is now clear. Reassemble the unit and power on.
● It may reboot several times to reconfigure itself.


ML210G-12

Drivers

https://drive.google.com/open?id=1QwP5iTUc2SwTKVPQyKKvrXJFgGtmXfNy

Motherboard Manual

https://drive.google.com/open?id=1TtHgHIty4b3MH6nvSg-l89T9jYTJz1xO

Enable Auto Power On

Note: This procedure requires opening the case first. Instructions for opening the case can be found here.

● Locate the PWR_JP1 jumper indicated by the orange
arrow and red circle

  • Move PWR_JP1 over by 1 pin
  • The unit is now configured for auto power on

Clear the CMOS

Note: This procedure requires opening the case first. Instructions for opening the case can be found here.

● Locate the clear CMOS jumper

  • Move the jumper over by 1 pin
  • Wait 30 seconds
  • Restore the jumper to its original position
  • The CMOS is now clear

ML210G-50

Drivers

https://drive.google.com/open?id=1RJPoD0gRRcAV-xkuIT6r_qmpW1V_BBh7

Motherboard Manual

https://drive.google.com/open?id=1xuo3h04jCT-49kdsB9PA31hZAZ67K2SI

Enable Auto Power On

● Locate the PWR_JP1 jumper indicated by the
orange arrows

● Move PWR_JP1 over by 1 pin
● The unit is now configured for auto power on

Clear the CMOS

  • Locate the clear CMOS jumper

● Move the jumper over by 1 pin
● Wait 30 seconds
● Restore the jumper to its original position
● The CMOS is now clear


Updated on June 19, 2020

Was this article helpful?

Related Articles

Need Additional Support?
Can’t find the answer you’re looking for? Don’t worry, we’re here to help!
Contact Support