1. Home
  2. OnLogic Systems
  3. Industrial Fanned Line
  4. MC500 & MC510 Technical Resources

MC500 & MC510 Technical Resources

The MC500 and MC510 can be opened by the user. This does not void the warranty, however, any damage caused by doing so will not be covered.

The following steps will walk you through opening your MC500 and/or MC510 case, as well as auto-powering on and clearing CMOS.

Opening the MC500 & MC510 Case

The case is very simple to open. To do so, remove the two screws from the back and slide the lid off towards the rear.


The following sections contain instructions on how to enable Auto Power on and clear the CMOS for your specific model. To jump to your specific model, view the product list on the right.

MC500G-10

Mitac PD11BI-P Motherboard

Motherboard Manual

https://drive.google.com/open?id=1X9BdH34UMrzS9n-KNdNjooRbr_t6gZAl

Drivers

https://drive.google.com/open?id=1gvW9DaS29yZJf243pQ4oxGfV2ax6BYKS

Auto Power On

  1. Power on the unit and press the Del key to access the BIOS
  2. Navigate to the Chipset tab
  3. Change “Restore AC Power Loss” to [Power on]
  4. Save changes and exit. Auto power on is now enabled.

Clear CMOS

  1. Locate the clear CMOS jumper
  2. Move the jumper over by 1 pin
  3. Wait 30 seconds
  4. Restore the jumper to its original position
  5. The CMOS is now clear

MC500G-30

Mitac PH12LI-P Motherboard

Motherboard Manual

https://drive.google.com/open?id=1b169jNmg6aYm4gknHhkPZPyaBqjM60R2

Drivers

https://drive.google.com/open?id=1gzxFagz3ZWfDi7afXqg9SFpeFZNGZD9Q

Auto Power On

  1. Power on the unit and press the Del key to access the BIOS
  2. Navigate to the Chipset tab
  3. Open the PCH-IO Config menu
  4. Change “State After G3” to S0
  5. Save changes and exit
  6. Auto power on is now enabled

How to Clear CMOS

  1. Locate the CMOS battery
  2. Carefully disconnect the white connector
  3. Wait 5 minutes
  4. Reconnect the white connector
  5. The CMOS is now clear

MC500G-50

ASRock IMB-180 Motherboard

Motherboard Manual

https://drive.google.com/open?id=1pgxuCqbYT1mdY7Wht5JZbsZP8fBoLmPg

Drivers

https://drive.google.com/open?id=1RGYB0C90fm1qmc2LJzz8HILXeG7uh9dg

Auto Power On

  1. Locate the AT/ATX jumper
  2. Move it over by 1 pin
  3. Auto power on is now enabled

How to Clear CMOS

  1. Locate the CLRMOS1 jumper
  2. Move the jumper over by 1 pin
  3. Wait 30 seconds
  4. Restore the jumper to its original position
  5. The CMOS is now clear

MC500G-51

ASRock IMB-195 Motherboard

Motherboard Manual

https://drive.google.com/open?id=12vOyAy8vuB0YlUG2v3wUMsoA-obvbsuE

Drivers

https://drive.google.com/open?id=17HrQDHq6T1wK0dzS8-3OCSR1bVE6aGLU

Auto Power On

  1. Locate the AT/ATX jumper
  2. Move it over by 1 pin
  3. Auto power on is now enabled

How to Clear CMOS

  1. Locate the CLRMOS1 jumper
  2. Move the jumper over by 1 pin
  3. Wait 30 seconds
  4. Restore the jumper to its original position
  5. The CMOS is now clear

MC510-10

Motherboard Manual

https://drive.google.com/open?id=1MfhkgP-nIvFr2dgr_zUESwelq7knS7hW

ASRock IMB-156 Motherboard

Drivers

https://drive.google.com/open?id=1Qxk2BYDbPggBa89RNpVPdkqu640DIPmh

Auto Power On

  1. Locate the PWR_JP1 jumper indicated by the orange circle
  2. Move PWR_JP1 over by 1 pin
  3. The unit is now configured for auto power on

How to Clear CMOS

  1. Locate the clear CMOS jumper
  2. Move the jumper over by 1 pin
  3. Wait 30 seconds
  4. Restore the jumper to its original position
  5. The CMOS is now clear

MC510-40

ASRock IMB-V1000M Motherboard

Motherboard Manual

http://download.asrock.com/IPC/Manual/IMB-V1000.pdf

Drivers

https://www.asrockind.com/IMB-V1000

Enable Auto Power On

  1. Power on the unit and press the F2 key to access the BIOS
  2. Navigate to the Advanced tab
  3. Open the Chipset Configuration menu
  4. Change “Restore on AC/Power Loss” to [Power On]
  5. Press F10 to save changes and exit
  6. Auto power on is now enabled

Clear the CMOS

  • Locate the clear CMOS jumper
  • Move the jumper over by 1 pin
  • Wait 30 seconds
  • Restore the jumper to its original position
  • The CMOS is now clear

MC510-50

ASRock IMB-1212 Motherboard

Motherboard Manual

https://download.asrock.com/Manual/IMB-1212.pdf

Drivers

https://drive.google.com/open?id=1l9imqOhuOHG4bkKDXCb7vxUODlV-qX8m

Auto Power on

  • Locate the jumper circled in red and the pin header circled in orange
  • Remove the red jumper and install it on the orange header.
  • The red jumper controls LVDS voltage, which is not used in this system. It can safely be taken for use on the auto power on header.
  • Auto power on is now enabled

Auto Power On (older boards)

IMB-1212 motherboards manufactured before June 2020 use a different jumper for auto power on. This jumper is not present on the newer boards.

  1. Locate the PWR_JP1 jumper indicated by the orange circle
  2. Move PWR_JP1 over by 1 pin
  3. The unit is now configured for auto power on

How to Clear CMOS

  1. Locate the clear CMOS jumper
  2. Move the jumper over by 1 pin
  3. Wait 30 seconds
  4. Restore the jumper to its original position
  5. The CMOS is now clear
Updated on June 5, 2020

Was this article helpful?

Related Articles

Need Additional Support?
Can’t find the answer you’re looking for? Don’t worry, we’re here to help!
Contact Support